Reasons for early failure of oil seals

Aug 14, 2022

Oil seal sealing principle: When the oil seal is in a free state, the inner diameter of the lip is smaller than the outer diameter of the journal. Even if there is no spring, there is a certain radial pressure on the journal. Add a spring to compensate. The orientation of the installation also makes the lip more closely attached to the shaft when it is under pressure inside the box, ensuring that the contact pressure of the lip to the journal is evenly distributed and concentrated. When the shaft rotates, the journal and the lip form a sealing belt with a width of 0.3-0.5 mm, and an oil film with a thickness of about 0.003 mm is maintained in the annular sealing belt. The oil film makes the lip and journal work under the condition of close to liquid friction, which plays the role of lubricating the journal and reducing the wear of the lip. A thin and uniform oil film can be maintained between the lip and the journal, which is the best state of oil seal work. In this case, a small amount of oil will seep out to wet the journal on the outside of the lip. Although it may be detrimental in appearance due to dust, it is a sign that the oil seal is working well and should never be regarded as a malfunction. With the wear of the lip and the increase of the thickness of the oil film, the leakage of oil will gradually increase. At this time, if the spring can be shortened in time to keep the radial pressure of the lip within a suitable range, the oil seal can still recover well. performance. Only when the inner diameter of the lip is smaller than the journal in the free state due to excessive wear, and the radial pressure is maintained by the spring alone, the work of the oil seal will enter an unstable state. It can be seen that under normal working conditions, the oil seal can work in good condition for a long time. In production practice, the service life of oil seals is long or short, and the difference is large. Some can reach 2 overhaul intervals, while others have very short working hours, and even oil leaks at the beginning of work. Replacing the oil seal to solve the problem of oil leakage accounts for a large proportion of the man-hours consumed in equipment maintenance operations. Therefore, for the oil seal that has lost its function, especially the oil seal that fails in the early stage, it is not just a simple replacement of the oil seal, but the definite cause of the failure of the oil seal should be found out, and effective maintenance measures should be taken according to the main points of the problem.

The reasons for the early failure of the oil seal are analyzed as follows: 1. The pressure in the box is too high. Under normal circumstances, the oil seal can withstand an internal pressure of 1kg/cm2. If the pressure in the box is excessively increased, exceeding the pressure-bearing capacity of the oil seal, the leakage will increase significantly. For example, poor ventilation of the crankcase, blockage of the ventilation holes of the transmission and rear axle housing, and serious leakage in the oil pump will become the triggering factors for the failure. When the abnormality occurs in the above places, the following phenomena will also occur: the screws running through the inner cavity of the box and the paper pads between the joint surfaces will also leak oil. Oil seals are divided into low-speed type and high-speed type. Replacing the high-speed type with a low-speed type will greatly reduce the service life. The low-speed type is suitable for linear speed V≤6m/s, and the high-speed type is suitable for V=4~12m/s. The selection of oil seals is not comprehensive only if the size is appropriate. You should also check the performance description to determine whether the model is correct. 3. The shaft pump is loose. The looseness of the shaft pump will cause the eccentricity of the journal, which will cause the oil seal lip edge to bear a large difference in load along the circumference, causing early wear. 4. The journal is rough and the finish is too low. The smoothness of the journal should not be lower than 7-8, otherwise the lip of the oil seal will wear quickly. When the oil seal is installed in the base, because it is not pressed evenly with a suitable pressing tool, but is knocked in with a hard knock, the result is that the oil seal body is skewed and the skeleton is deformed, and the lip is out of alignment in the correct position of the space. The oil seal grinding hole is not concentric with the shaft journal. Misalignment will cause uneven radial pressure distribution on the oil seal lip, which will also lead to the same consequences. For example: the crankshaft front oil seal of some models of engine, because the timing cover as the oil seal base has no positioning device on the front end of the cylinder block, if the centering treatment is not done during installation, it will cause the oil seal and the crankshaft bearing. misalignment deviation. The oil seal spring is missing or knocked off during assembly. If the oil seal of the half shaft and the rear oil seal of the crankshaft of some models are not carefully installed, not only the spring will fall off, but also the body will be deformed. Oil seal lip and journal surfaces are not greased during assembly. Since there is no oil film that must be given manually at first, the oil seal is in a state of wear once it starts to work. Dry wear will generate high temperature, which is easy to burn the lip, and the rubber adheres to the journal. 9. During the installation process, the burrs at the chamfer of the journal, the thread at the front end of the journal, the key teeth, etc., will scratch the lip when passing through the lip. For example: when the vertical arm shaft is installed in the steering gear, the triangular key teeth on the shaft end can easily scratch the oil seal lip. This is the real root cause of oil leakage when many steering gear oil seals are installed. The correct method is: first insert the tapered cardboard into the oil seal lip, and wait until the conical spline part of the shaft head passes through the lip under the isolation of the cardboard. , and then carefully pull out the cardboard. The burrs, sharp edges, rust spots and scars on the journal before installation must be ground and cleaned in advance. 10. The temperature of the box body is abnormally high, the oil is not clean, and the impurity content is too high, which will also accelerate the aging and wear of the oil seal. Improper storage of oil seals and long storage period will cause rubber aging, mildew, shrinkage, and greatly reduce the working capacity.


You Might Also Like